Hire

Wisycom MTK952N-2W0-MS-DC

Now available for hire/rental

DIGITAL SYNTHESIS "MONO/STEREO/INTERCOM" MODULATION
HIGH PERFORMANCE DSP AUDIO PROCESSING
MTK952 is a versatile dual transmitter capable of working in a huge 330Mhz UHF bandwidth and of generating any kind of narrow-band modulations, with very high quality and low spurious emissions. Up to 2 watt RF output per channel.

This model N-2W0-MS-DC also offers master or slave options for MFL optical link as well as a 12 volt opperation.

UHF RACK TRANSMITTER 330 MHz BANDWIDTH
MONO/STEREO/INTERCOM digital direct synthesis (DDS)
MASTER-SLAVE configuration for isofrequency network
DSP audio with low latency and AES3 input
Powering VAC 110/230 & VDC 10/28
10mW-2W 470-798 mono/stereo TX - N connector

Switchable channels2400 allocated by 40 groups of 60 channels quickly selectable with dedicated buttonsFrequency bandwidth470-800 MHzSwitching bandwidth330 MHz tuneable in 5 kHz stepsTemperature range-10 ÷ +55 °CRF output powerSelectable: 10,20,50,100,200 mW, 2000mW (ERP)
MTK952-2W0: 2Watt 
[NOTE] RF power can be limited on frequency base accordingly to specific country restrictions (software based)“TX1” / TX2” antenna outputwith BNC type female connectors (for MTK952)
with N type female connectors (for MTK952N)M-S I/O2x BNC type female connectors (only for MTK952N with MS option)RF impedance50 ΩSpurious emissions< 2 nW (in the transmitter bandwidth)ModulationFM, MPX Stereo or mono, selectable with dedicated menuPeak deviation±56 kHz for mono, ±48 kHz for stereo (preset mode)
NOTE: custom setting can set peak deviation from 2kHz to 100kHzMPX Pilot tone19kHzTone squelch32.789Hz (for Wisycom wireless microphone, i.e. ENR/ENC)
131,8 (for Wisycom intercom, i.e. NR) 
NOTE: custom setting can change the Tone squelch (30-260Hz and 18K-38KHz)Frequency response20÷20kHz (mono)
30÷15kHz (stereo)
NOTE: custom setting can change audio bandwidth (3/4/12/15/20kHz)Analogue audio inputConnector type : XLR-3 / 1/4“ (6,3mm) jack combo socket, electronically balanced
Max. input level : +18dBu
Pin Assignments : XLR: 1=ground 2=hot 3 =cold; 6.35mm (1/4”) TRS: Tip=hot Ring=cold Sleeve=groundMonitor outputConnector type : 6.35mm (1/4”) jack socket, balanced
Monitor output level : max 120+120mW @ 24 Ohm, 80+80mW @ 150 Ohm
Monitor out impedance: 25 Ohm for auricleDigital audio inputAES3 on XLR-3M (32kHz ÷108 kHz)CompanderENR (Wisycom Extended-NR), with independent Attack- and Recovery-time, noise optimized
ENC (Wisycom Extended-NC), with independent Attack- and Recovery-time, voice optimized & with reduced pre-emphasys
NONE-d50 , no compander, pre-emphasis 50 µs
NR , to work with Wisycom Intercom system 
Other compander on requestDisplay64 x 256 OLED (yellow)Configuration/monitor interfaces10/100 Base TX Ethernet port on RJ45 connectorPower supply90 - 264 V AC, 50/60 Hz
10 – 16 VDC, Max 7A (option DC )Dimensions19”/1U 483 x 407 x 43,8 mm (WxDxH) with bracketsWeight3.8Kg (version 200mW with DC and MS options); 
4Kg (version 2Watt with DC and MS options)